Show us why the public should always call a land surveyor

Where are you surveying?


🌐 Show Forums for All Locations
Land Surveyor Community

Topographic Survey

Friends... I m using Sokkia FX 101 1"  I am facing problem in topographic surveying. Actually i m not sure how to do topographic survey. What's the procedure of topographic survey. Each time we place the total station to a new position we have to change instrument height or not. is there a need to give prism height. i need to know complete method of topographic surveying (contour surveying what we call locally). also provide me manual of sokkia FX 101... any information will be helpful.

Please help me out guys asap...

You need to be a member of Land Surveyors United - Global Surveying Community to add thoughts!

Join Land Surveyors United - Global Surveying Community

Votes: 0
Email me when people reply –

Replies

  • Can Anyone provide me a manual for Sokkia FX 101 1"... any help will be helpful

  • Land Surveyor

    You can do a topographic survey with a total station using a method called trigonmetric leveling. There are several ways of doing it depending on your hardware and software combinations you are utilizing. Here is a basic outline.

    Information needed.

    1) Reference datum (some known benchmark you wish to relate your topographic survey to). You can assume a starting elevation if you wish.

    2) Height of instrument (this is measured from the top of the mark your total station is set up on to the line or hole that is on the same plane as the scope). You can adjust this measurement for a true instrument height if you wish, although this is typically not necessary.

    3) Height of prism (this is measured from bottom of pole to center of prism). = HP

    What you record for each observation.

    1) Zenith angle, slope distance and horizontal angle. (Most modern total stations contain a function where you can ask it to display the prism difference "PD" instead of the slope distance and Zenith angle and you can record that instead but you need the slope or horizontal distance to locate your point horizontally relative to your total stations location.)

    How you determine elevations. (I recommend that you always run a conventional control elevation loop through your control points using a level but there are several methods for performing the necessary double checks to assure your results).

    1) Set your total station up over a known control point (you know the elevation of it) and backsite a known control point (you know the elevation of it also). This is done so you can check to make sure you have done everything right BEFORE you start making observations.

    2) Add the height of instrument (HI) to the elevation of the control point you are setup on. (BM elevation + HI = Elevation of instrument or EI).

    3) Make an observation on your backsite point. The Slope distance times the sine of the Zenith angle gives you the prism difference or (PD). The PD is subtracted (or added, depending on the result) from your EI. You then substract the HP to obtain the elevation of the point you located.

     

    • Thanks for your immense reply ... it helped me a lot ... sorry for my late thanks.... 

    • Hi Deward!

      Taking time to reply with that length and details, I can tell you're a real surveyor at heart..

      Have a pleasant afternoon from the Philippines.

      Regards,

      Arnel

      • GEO Ambassador

        YES!  You two guys should definitely meet.  I must say that you two are by far two of the most dedicated and passionate surveyors that I know from your respective areas of the world, if not the entire world.  Thank you both for continuing to help other members in need!  This is what it is all about!

This reply was deleted.

Answer As your Facebook Page

Global Surveyor Forum

Latest Discussions by Category

How to Utilize Surveyor Forums

How to use Forums
Our forums on Land Surveyors United are here to be used as much for finding help with problems in the field as the are for you to express your opinions on anything that has to do with land surveying in general. Feel free to share anything that is on your mind, as long as it isn't meant to damage another member's reputation. Please keep it clean and help insure that everyone has the opportunity to enjoy the benefits of being part of a community that grows together.

We are committed to allowing freedom of expression for all of our members, and that includes maintaining a safe space for people with opposing views to express themselves. We get posts from all over the country and even the globe, so needless to say, people come with different viewpoints on lad surveying practices and processes. We see this diversity and variety as a real strength-- dialogue and debate are an integral part of the educational process, as well as an important tool in exploring different sides of complex issues.

All Community Hubs inside the community have their own forum for asking specific questions to other surveyors, by location, equipment type, etc.

Topics by Tags

Monthly Archives

Global Forums

Add Your Expertise

🌐 Explore Forums Based on Location

Blog Topics by Tags

Monthly Archives