Nimal Jayamaha
  • LYNBROOK
  • Australia
Share on Facebook
Pass This On
  • Blog Posts
  • Discussions (7)
  • Surveyor Support Group Forums
  • Surveyor Photos
  • Photo Albums
  • Land Surveyor Videos

Nimal Jayamaha's Discussions

SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?

Started this discussion. Last reply by Carlo Alberto Birocco May 20. 8 Replies

I'm running a SOKKIA SRX with SurveCE on Carlson Surveyor+ data collector. We mainly do Urban/ Semi-Urban cadastral surveys. In one man operation tried to use Robot mode. I've setup a tripod and set…Read more →

Low Cost RTK Receiver - EMLID REACH RS

Started this discussion. Last reply by Dmitriy Ershov Dec 20, 2017. 22 Replies

EMLID recently released a field ready low cost RTK receiver. EMLID website says it's ready for surveying, mapping, monitoring & robotics. One receiver price only $799. Satellite Tracking:GPS/QZSS…Read more →

Subject Tags: GNSS, RTK, EFFECTIVE, COST

Boosts Received

Gift

Nimal Jayamaha has not received any Boosts yet

Say Thanks!

 

Nimal Jayamaha's Profile

Community Feed

Nimal Jayamaha's discussion was featured

SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?

I'm running a SOKKIA SRX with SurveCE on Carlson Surveyor+ data collector. We mainly do Urban/ Semi-Urban cadastral surveys. In one man operation tried to use Robot mode. I've setup a tripod and set the ATP1 360 prism for backsight & foresight. In TRACKING & SEARCH modes the gun locks to slightly off the visible centre towards right. For 100-150m it's about 10-12 seconds. Approximately for 150m - 7mm, for 100m - 5mm, for 50m- 2mm off respectively. If I set 0.0000 for backsight, after…See More
Monday
Carlo Alberto Birocco replied to Nimal Jayamaha's discussion SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?
"Nimal, what Ivan and Troy wrote above is absolutely correct. Due the image processing, your SRX achieves better accuracy in angular measurements. This is an AP1 image from SRX camera during a service inspection in my lab: Sorry for image quality,…"
May 20
Ivan replied to Nimal Jayamaha's discussion SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?
"Good explanation, it is not an error, it is the way the station works, moreover you can check the accuracy of your targets looking the residuals of your resections, and the results of your backsights"
May 20
Troy Deaton replied to Nimal Jayamaha's discussion SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?
"The SRX has a field collimation process that can correct this issue. Setup prism about 300ft away and go to the configuration/collimation IMAGE-SENSOR is normally the last in the list. Sight prism center and press measure and it will do an…"
May 20
Ed DeSaulniers replied to Nimal Jayamaha's discussion SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?
"How did you determine there was a difference? They robot will only mechanically turn near the target and once the target is close it will only fine tune electronically. So the cross hair will not necessarily be lined up on the ATP1. Also when using…"
May 20
Ivan replied to Nimal Jayamaha's discussion SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?
"Hi, I copied this comment from my Sokkia SRX manual, hope it helps Search operation during Auto Pointing 2. When the target enters the field-of-view within the set time limit for Auto Pointing completion, the SRX stops moving and the offset between…"
May 19
Benjamin J Everett replied to Nimal Jayamaha's discussion SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?
"It’s a radio link collimation. I would do a zero point collimation on the zenith as well."
May 19
Kris Melaram favorited Nimal Jayamaha's discussion SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?
May 19
Kris Melaram favorited Nimal Jayamaha's discussion SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?
May 19
Kris Melaram favorited Nimal Jayamaha's discussion SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?
May 19
Stephen B Newbill replied to Nimal Jayamaha's discussion SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?
"There is a difference between the electric eye and manual sighting. And there is a calibration for it. The robot should know when you are manual sighting and electrical sighting. The manual should help you find it... Typically you will get better…"
May 19
Nicolas replied to Nimal Jayamaha's discussion SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?
"Have you calibrated your station recently?"
May 18
Nimal Jayamaha posted a discussion

SOKKIA SRX ROBOT IS NOT TRACKING ATP1 360 PRISM CENTRE ?

I'm running a SOKKIA SRX with SurveCE on Carlson Surveyor+ data collector. We mainly do Urban/ Semi-Urban cadastral surveys. In one man operation tried to use Robot mode. I've setup a tripod and set the ATP1 360 prism for backsight & foresight. In TRACKING & SEARCH modes the gun locks to slightly off the visible centre towards right. For 100-150m it's about 10-12 seconds. Approximately for 150m - 7mm, for 100m - 5mm, for 50m- 2mm off respectively. If I set 0.0000 for backsight, after…See More
May 18
Nimal Jayamaha replied to Peter Hunt's discussion Trimble TSC3 Compatibility
"If you're using TSC3 with Trimble Access, now Access fully supports Spectra Precision SP80 as well."
Mar 20
Nimal Jayamaha replied to Peter Hunt's discussion Trimble TSC3 Compatibility
"Hi Peter, Sorry about late response. If you haven't found the right answer yet, I think this might be useful. CHC i80 works with SurveCE Version5 & CHC Landstar 7. TSC3 works with SurvCE V2.62, V3, V4 & V5. You find this info…"
Mar 12
Dmitriy Ershov replied to Nimal Jayamaha's discussion Low Cost RTK Receiver - EMLID REACH RS
"Sure! Reach RS takes raw data from m8t and uses Emlid's version of rtklib to calculate precise position. "
Dec 20, 2017

Profile Information

I am here because I am a.
Professional Land Surveyor
Surveyor Bio:
Professional Land Surveyor who started with old school surveying in 1986
Company
R. D Carter & Associates
Location for Member Map
Australia
Licenses Certifications or Awards
Licensed Surveyor Sri Lanka
I have experience with the following
cadastral, topographic, boundary surveys, topographic surveys, GIS
How many years have you been surveying?
More than 20 yrs
Most comfortable with the following types of instrumentation
Total Stations, Surveying Software, Old school surveying, theodolite

Comment Wall (1 comment)

At 9:41am on June 18, 2017, Padukkage Nalin Pushpakumara said…

Dear Mr. Nimal Jayasighe,

I am Sri Lankan Surveyor, currently employed in Nowaloka Construction Company , 5 yrs of experiences. graduated from ISM.

Currently I am looking for a job opportunity in Australia, If  you have a such opportunities pl let me know then I could forward my CV.

Thanks,

Nalin Kumara

 
 
 

Where Thousands of Professional Land Surveyors, Students of Surveying and Educators are United through Collaborative Knowledge and Purpose.

Tools,Apps and Quick Guides

Surveyor Community Hubs For World Regions

Surveying Hubs For US States

Social Support For Equipment

Surveying Photos by Tag

Surveying Videos by Tag

BMC logoSupport Us! +LandSurveyorsUnitedon Google+

Next Generation Land Surveyor Community Where Every Day is a Surveying Conference

Surveyor Birthdays

© 2018   © Created by Land Surveyors United   Powered by

Badges  |  Contact LSU  |  Privacy Policy  |  Terms of Service